WhatsApp: +86 139 2872 8741
Email: [email protected]
Tel:
0086-757-8938 9313
0086-20-8938 9313
Address:
Caochang Industrial Area, Liguang Rd, Lishui, Nanhai, Foshan, Guangdong, China
Reply within 1 hour, 24x7 online service
WhatsApp: +86 139 2872 8741
Email: [email protected]
Tel:
0086-757-8938 9313
0086-20-8938 9313
Address:
Caochang Industrial Area, Liguang Rd, Lishui, Nanhai, Foshan, Guangdong, China
Reply within 1 hour, 24x7 online service
The problem in one line: a food court runs on steam, grease vapor and hourly wipe-downs, and most glowing signage is simply not built for that routine. An el panel food court plan works when hygiene and power rules are designed in from the first drawing.
We manufacture electroluminescent panels in Foshan, and mall operators ask us the same question before every fit-out: where can a glowing panel go in a food court, and where should it never go? This guide answers with a placement map, a cleaning routine tenants actually follow, and the power rules that pass inspection. For the small close-range format at tables, our table card guide covers the tent-card build.
| Item | Typical figure or rule |
|---|---|
| What it is | A 0.3-0.5 mm laminated EL sheet with an even glow face, driven by a low-voltage inverter |
| Panel brightness | 80-140 nits; fresh panels start near 140 nits and fade gradually |
| Best fit zones | Menu headers, pillar wraps, queue rails and table tops in dim to mid light |
| Face protection | Laminated wipe-clean face; bare panels are not wipe-rated |
| Cleaning rule | Soft cloth plus mild detergent; never spray the panel directly |
| Ingress stance | A panel is not washdown equipment; keep it out of jet, hose and steam paths |
| Power input | 12V DC or AC adapter on the display side; SELV keeps the face-side voltage low |
| Inverter placement | Dry, ventilated, serviceable spots away from steam, grease and water |
| Wiring | Concealed routes away from heat; fixed mains work by a local electrician |
| Lead times | Sample within 7 days of mockup approval; bulk 7-10 days; roll-outs 15-20 days |
An EL panel is a thin laminate that emits light across its whole surface. The stack runs from a printed graphic film through a phosphor layer between two electrodes, finished at 0.3-0.5 mm. Because the glow comes from the material, the face carries no bulbs, no hotspots and no heat worth mentioning.
An inverter converts the venue supply into the alternating field the panel needs, and the display side runs at low voltage. The panel draws power at phone-charger scale, so a stall can light a full menu header without touching its kitchen circuits. The laminate bends gently to a radius of about 5-10 mm, which is enough for pillar wraps but not for sharp folds; our bending limits guide shows where the safe line sits.
A food court combines four stresses that ordinary retail never mixes: steam rising from tea and noodle stations, grease vapor settling on every horizontal face, cleaning crews wiping surfaces every hour, and trading days that run twelve hours or more. Any display material that ignores one of these four will look tired within a season.
The industrial design world sums it up in one sentence worth borrowing: the cleaning procedure should become part of the equipment requirements. Decide first how often the surface gets wiped, with what agents, from what distance, and then choose the build. A panel specified backwards, chosen before the cleaning routine, is the one that peels, dims or fails inspection first.
Staff turnover adds a human layer. The tenant who cleans today is not the crew who cleans next month, so the rule set must live on a laminated card at the stall, not in an email thread. We ship that card with every order, and section six below is essentially its text.
Buyers often arrive asking for an IP rating by number. The better question is the reverse: describe the cleaning, then let the rating follow. The ladder below is the industry convention.
| Cleaning reality | Protection level | Display takeaway |
|---|---|---|
| Cleaning reality | Protection level to expect | What it means for a display |
| Dust and occasional splashes | About IP54 | Light-duty enclosures; faces wipe clean |
| Low-pressure water jets | About IP65 | Sealed enclosures; direct spray tolerated |
| Powerful jets or heavy wet cleaning | About IP66-IP67 | Fully sealed builds with sealed entries |
| High-pressure hot washdown | IP69K territory | Purpose-built equipment, not display signage |
Now the honest application. An EL panel is a mounted display, not washdown equipment. Our laminated faces are wipe-clean by design: a damp cloth with mild detergent, spilled drinks and oil mist wiped promptly, and the panel keeps serving. What no display-grade build should promise is jet or hose tolerance, and we will not write that on a datasheet.
The second lesson from food-grade design matters even more than the number: the interfaces are the weak points, not the face. Cable entries, connectors and edge seals admit water long before a laminated face does. That is why our placement guidance spends more words on cable exits and edge sealing than on brightness, and why a monthly interface check is part of the routine below.
Cleaning chemistry rounds out the picture. Repeated exposure to aggressive agents attacks plastics and laminates cumulatively: first discoloration, then swelling, then cracking. The agents that keep a laminate healthy are the boring ones, which is exactly what the next section prescribes.
Placement decides survival more than any specification. The zone map below comes from fitted-out courts and reflects the splash line of a typical stall counter.
| Zone | Fit | Placement rule |
|---|---|---|
| Zone | Fit | Placement rule |
| Stall menu headers | GOOD | Mount above the splash line; cable exit faces up or rear |
| Pillar and column wraps | GOOD | Curved laminated panels; sealed edges; wipe with the grain of the wrap |
| Queue rail inserts | GOOD | Flat panels in rigid holders that staff can lift out for cleaning |
| Table top tent cards | GOOD | Small sealed cards; wipe like the table itself |
| Above tea and fryer stations | SKIP IT | Steam and grease vapor shorten laminate life; use a printed board |
| Inside washdown or hose paths | SKIP IT | No display-grade build belongs in a jet path |
Light level shapes the same map. Court aisles often sit in bright mall lighting where a glow face reads pale; counter zones, pillars under mezzanines and evening seating pockets sit dimmer, and there the glow earns its wall. Match the panel to the lux level, and the budget follows honestly. The venue types at the dim end of the scale, such as bar counters and hotel lounges, are covered in our hotel and bar guide.
1. Keep the display side low voltage. Panels run from a 12V DC input or an AC adapter, so the face side stays at safe extra-low voltage. Guests and staff only ever touch the low-voltage side.
2. One inverter per panel, sized to the load. Do not chain two panels to one small driver. We match inverter ratings to panel area in writing, and the connector keying makes a wrong pairing awkward to force.
3. Route cables away from heat and water. Concealed runs along the rear of headers, never across stove backsplashes or under sink cabinets. Cable exits sit where the cleaning cloth cannot snag them.
4. No daisy-chained power strips. Each stall draws its display power from the circuit the electrician assigned, not from a kitchen extension lead. Where local code requires residual-current protection on that circuit, the electrician confirms it at sign-off.
5. Keep inverters serviceable and dry. Drivers live in ventilated spots the crew can reach for checks, away from steam clouds and fryer updrafts. A driver that overheats dims its panel long before it fails, which our dimming causes guide explains.
1. Dry dust first. A dry microfibre pass lifts crumbs and dust so the wet step never drags grit across the face.
2. Damp cloth, mild detergent. Wring the cloth properly and wipe the laminated face in light strokes. The cloth carries the water; the panel never receives a spray.
3. Keep the off-list off the panel. No solvents, no abrasive pads, no ammonia sprays and no steam cleaners pointed at the face. Each attack on the laminate is small, and the damage adds up over months.
4. Wipe spills the same hour. Syrup, oil mist and sauce salt out and etch when left overnight. The daily close-down card ends with this line for a reason.
5. Check edges, cables and brightness monthly. Look at the edge seals, tug the cable glands gently, and compare glow against the neighbouring panels. A panel drifting dim early gets flagged to us before it dies; our lifespan guide separates normal fade from a fault.
The honest verdict table, stated once, saves both sides a season of friction.
| Situation | Verdict | Why |
|---|---|---|
| Situation | Verdict | Why |
| Menu headers above the splash line | WORTH IT | Even glow keeps the menu readable through evening dimming |
| Pillar wraps in dim aisles | WORTH IT | Curved laminate turns dead columns into brand faces |
| Table top cards on wipeable tables | WORTH IT | Sealed small cards survive the same cloth as the table |
| Behind tea, fryer or grill stations | SKIP IT | Steam and grease vapor beat the laminate down within a season |
| Washdown walls and hose paths | SKIP IT | No display-grade build belongs in a jet path |
| Open atriums in mall daylight | SKIP IT | 80-140 nits reads pale under bright daylight |
1. Audit the cleaning regime per zone. Write down wipe frequency, agents and spray distance for each position. The audit picks the build, not the other way round.
2. Draw the splash lines. Walk each stall with the operator and mark where water and vapor actually reach. Panels go above the line, equipment stays below it.
3. Order laminated faces with sealed edges. The laminate and edge seal are what make daily wiping safe. Confirm both in the written spec, along with cable exit positions.
4. Plan power with the electrician. Assign one low-voltage route per stall, mark inverter placements, and keep the mains side inside the licensed scope. Send us the drawings and we match connector positions.
5. Pilot one stall for a full cycle. Run a complete service day including cleaning shifts. Adjust placement, brightness and the cleaning card before the court-wide order.
6. Scale from one batch. Order the full quantity from the production run the pilot proved, or hold spares from it, so tone and brightness stay uniform across stalls. Our coffee shop guide shows the same pilot-then-scale logic at shop scale.
Spraying the panel directly. The single most common failure trigger. The cloth gets the liquid, never the face.
Mounting inside the splash zone. A panel six centimetres above a sink lives a hard life. Move it above the line and the same panel lasts for years.
Burying inverters behind steam equipment. Heat and humidity cut driver life sharply. Ventilated, serviceable, dry: three words that decide the mount.
Chaining panels to undersized drivers. Overloaded inverters run hot and dim the display within weeks. One driver per panel, matched to area, in writing.
Reordering from a new batch without a colour check. Batch drift shows as tone differences across stalls. Order complete quantities together or hold spares from the proven batch.
| Feature | Advantage | Benefit |
|---|---|---|
| Feature | Advantage | Benefit for the operator |
| 0.3-0.5 mm laminated face | Wipes clean with the daily routine | No special cleaning crew or product needed |
| Even 80-140 nits glow | No hotspots behind the menu text | Headers stay readable as the court dims |
| Cool operation | Safe next to guests and packaging | No heat add-on in already warm counters |
| Phone-charger power draw | Display power skips kitchen circuits | Electricians sign off fit-outs faster |
| Curvable laminate | Wraps pillars and column faces | Dead structural columns become brand faces |
| Factory direct from Foshan | Sealed edges and cable exits built to order | Fit-out drawings match the panels on arrival |
1. Direct factory source better control quality. Laminating, edge sealing and electrical testing happen in our Foshan facility. When a food court operator needs a sealed edge or a specific cable exit, the change reaches the line the same day.
2. 15+ years professional experience. We have produced electroluminescent displays since the early 2000s for food, beverage and retail clients, so we know which placements survive wipe-down regimes and which do not.
3. Smooth communication & fast response. One named contact follows your order from quote to shipping. We reply within 1 hour, 24×7, and we put cleaning limits and power notes in writing.
4. Small qty acceptable. Custom EL products start from 5 pcs per design. Pilot one stall, measure the service routine, then roll out to the rest of the court.
5. Cooperated with more than 100+ global brands. Work for food, beverage and retail clients across Europe, the Middle East and the Americas taught us the hygiene and electrical expectations each market applies.
6. Stable lead time & fast delivery. Sampling and bulk dates are confirmed in writing before the deposit. We flag an unrealistic opening date before you commit, not after.
A laminated face tolerates a soft cloth with mild detergent, which is what most daily routines use. Solvents, abrasive pads and ammonia-based sprays attack the laminate over time, and the damage is cumulative, so the cleaning card we ship with each order states exactly which agents stay off the panel.
The display side runs at low voltage through the inverter, the panel itself stays cool to the touch, and nothing on the face reaches cooking temperatures. Fixed installations still need the mains side wired by a local electrician to local code, and we mark that boundary clearly in the packing documents.
A splash on a laminated face wipes off without harm. A bare or edge-damaged panel is a different story, and neither build is rated for jets or hoses, so panels must sit above the splash line and never inside a washdown path. If a panel gets soaked, power it down and ask us before reuse.
Panels run 80-140 nits, which reads clearly in dim to mid-light zones such as counters, pillars and table tops. Under bright mall daylight a glow face can look pale, so we plan placement around the lux level of each position instead of promising one panel for every wall.
Panels and inverters arrive pre-wired with connectors, so venue staff can hang and plug a portable build. Any fixed mains route is the local electrician’s work and must pass the venue inspection. We provide the layout drawings and cable-exit positions that make the electrician sign-off quick.
Start with one pilot stall for a full service cycle, then scale with the same panel batch to keep colour and brightness consistent. Reorders from a different batch can drift slightly in tone, so we recommend ordering the full court quantity at once or holding spare panels from the first run.
A food court forgives nothing: steam, grease, hourly wiping and long trading hours sit on every surface. An EL panel plan survives when the cleaning procedure is written first, panels sit above the splash line with laminated faces and sealed edges, and power follows the five low-voltage rules. Send us the zone map and the cleaning routine through our contact page, and we will return a placement plan, a spec sheet and a sample schedule within the hour.
Send the size, quantity and destination country. We reply within 1 hour with feasibility, MOQ and lead time in writing.
Reply within 1 hour, 24×7 online service · [email protected]
Tell us the product, size, quantity and destination country. Attach artwork if you have it.